Usb 1-1.2.1: Device Descriptor Read/64, Error -71
RB PI 4 4GB bootet, USB nicht funtkional
- kenadams_the
- Unerledigt
-
- #i
Hallo zusammen,
nachdem ich im internationalen Forum keine Rückmeldung bekommen habe, versuche ich es mal hier.
Ich habe einen neuen Raspberry Pi 4 aus einem Kit von Berrybase https://www.berrybase.de/neu/r…tarter-kit-schwarz?c=2383
Wenn ich Noobs starte (vorinstalliert oder selbst auf andere SD Karte geschoben) funktionieren die USB Ports , sobald dann aber Raspberry Os (32) oder Ubuntu (64) installiert wurden und booten, sind die Ports nicht funktional , ich kann Maus und Tastatur nicht verwenden.
Gestestet mit
- Verschiedenen Mäusen und Tastaturen
- Raspberry OS oder Ubuntu mit Noobs installiert oder mit Raspberry Imager direkt auf SD Karte geschoben
- Mit Powerbank (5V 2A)
- Offiziellem USB-C Netzteil (5,1V 3A)
- max_usb_current=1 in /boot/config.txt
- sdhci.debug_quirks=96 in /kicking/config.txt
- total_mem=1024 oder 2048 in /kicking/config.txt
- Abgezogenem Lüfter (warum auch immer)
Dice Power LED ist durchgehend an. Die Fehlermeldungen tauchen auch ohne angestecktes USB Gerät auf, bei dem gesammelten Output state of war immer der Funkdongle meiner Tastatur dran.
Irgendwo auf Reddit hatte jemand bei gleicher Fehlermeldung verbundene Pins der USB Buchsen wegen zu viel Lötzinn, das ist bei mir nicht der Autumn.
Dice USB Fehlermeldungen am Ende des Bootvorgangs
[ 21.984803] usb 1-i: device descriptor read/64, error -110 [ 22.254578] usb 1-1: new high-speed USB device number 3 using xhci_hcd [ 27.424802] usb 1-one: device descriptor read/64, mistake -110 [ 42.784813] usb ane-1: device descriptor read/64, error -110 [ 42.904959] usb usb1-port1: attempt power bike [ 43.614569] usb 1-1: new high-speed USB device number 4 using xhci_hcd [ 48.714854] usb 1-1: device descriptor read/viii, error -110 [ 53.914761] usb 1-1: device descriptor read/8, error -110 [ 54.184579] usb one-i: new loftier-speed USB device number v using xhci_hcd [ 59.274753] usb one-1: device descriptor read/viii, error -110 [ 64.474801] usb 1-one: device descriptor read/all, fault -110 [ 64.475191] usb usb1-port1: unable to enumerate USB deviceAlles anzeigen
dmesg komplett
[ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.iv.72-v7l+ (dom@buildbot) (gcc version 9.iii.0 (Ubuntu 9.three.0-17ubuntu1~20.04)) #1356 SMP Thu Oct 22 thirteen:57:51 BST 2020 [ 0.000000] CPU: ARMv7 Processor [410fd083] revision iii (ARMv7), cr=30c5383d [ 0.000000] CPU: div instructions available: patching partitioning lawmaking [ 0.000000] CPU: PIPT / VIPT nonaliasing information cache, PIPT instruction enshroud [ 0.000000] OF: fdt: Auto model: Raspberry Pi 4 Model B Rev 1.2 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] Reserved retentivity: created CMA memory pool at 0x000000001ec00000, size 256 MiB [ 0.000000] OF: reserved mem: initialized node linux,cma, compatible id shared-dma-pool [ 0.000000] On node 0 totalpages: 1012736 [ 0.000000] DMA zone: 2304 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 196608 pages, LIFO batch:63 [ 0.000000] HighMem zone: 816128 pages, LIFO batch:63 [ 0.000000] percpu: Embedded xx pages/cpu s49804 r8192 d23924 u81920 [ 0.000000] pcpu-alloc: s49804 r8192 d23924 u81920 alloc=20*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] ii [0] 3 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 1010432 [ 0.000000] Kernel control line: coherent_pool=1M 8250.nr_uarts=0 snd_bcm2835.enable_compat_alsa=0 snd_bcm2835.enable_hdmi=1 snd_bcm2835.enable_headphones=1 smsc95xx.macaddr=DC:A6:32:B7:58:F6 vc_mem.mem_base=0x3ec00000 vc_mem.mem_size=0x40000000 panel=ttyS0,115200 console=tty1 root=PARTUUID=4a0ad747-02 rootfstype=ext4 lift=deadline fsck.repair=yes rootwait quiet splash plymouth.ignore-serial-consoles [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) [ 0.000000] Inode-enshroud hash table entries: 65536 (guild: six, 262144 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] software IO TLB: mapped [mem 0x17cc0000-0x1bcc0000] (64MB) [ 0.000000] Retentiveness: 3655596K/4050944K bachelor (10240K kernel code, 745K rwdata, 2836K rodata, 2048K init, 856K bss, 133204K reserved, 262144K cma-reserved, 3264512K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] ftrace: allocating 31086 entries in 61 pages [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment filibuster is 10 jiffies. [ 0.000000] NR_IRQS: sixteen, nr_irqs: sixteen, preallocated irqs: xvi [ 0.000000] GIC: Using split EOI/Deactivate fashion [ 0.000000] random: get_random_bytes called from start_kernel+0x338/0x520 with crng_init=0 [ 0.000008] sched_clock: 32 bits at 1000kHz, resolution 1000ns, wraps every 2147483647500ns [ 0.000023] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275 ns [ 0.000100] bcm2835: system timer (irq = 17) [ 0.000740] arch_timer: cp15 timer(south) running at 54.00MHz (phys). [ 0.000755] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0xc743ce346, max_idle_ns: 440795203123 ns [ 0.000772] sched_clock: 56 $.25 at 54MHz, resolution 18ns, wraps every 4398046511102ns [ 0.000784] Switching to timer-based delay loop, resolution 18ns [ 0.001016] Panel: colour dummy device 80x30 [ 0.001048] printk: panel [tty1] enabled [ 0.001099] Calibrating delay loop (skipped), value calculated using timer frequency.. 108.00 BogoMIPS (lpj=540000) [ 0.001120] pid_max: default: 32768 minimum: 301 [ 0.001269] LSM: Security Framework initializing [ 0.001458] Mount-enshroud hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.001481] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.002733] Disabling retentiveness control group subsystem [ 0.002855] CPU: Testing write buffer coherency: ok [ 0.003359] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.004268] Setting up static identity map for 0x200000 - 0x20003c [ 0.004475] rcu: Hierarchical SRCU implementation. [ 0.005147] smp: Bringing upwardly secondary CPUs ... [ 0.006332] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.007653] CPU2: thread -ane, cpu two, socket 0, mpidr 80000002 [ 0.008910] CPU3: thread -1, cpu iii, socket 0, mpidr 80000003 [ 0.009065] smp: Brought upwardly 1 node, 4 CPUs [ 0.009081] SMP: Total of 4 processors activated (432.00 BogoMIPS). [ 0.009094] CPU: All CPU(s) started in HYP manner. [ 0.009106] CPU: Virtualization extensions available. [ 0.009921] devtmpfs: initialized [ 0.023534] VFP support v0.3: implementor 41 architecture 3 part xl variant 8 rev 0 [ 0.023778] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.023807] futex hash table entries: 1024 (lodge: 4, 65536 bytes, linear) [ 0.030458] pinctrl core: initialized pinctrl subsystem [ 0.031520] Cyberspace: Registered protocol family 16 [ 0.035464] DMA: preallocated 1024 KiB pool for atomic coherent allocations [ 0.036041] inspect: initializing netlink subsys (disabled) [ 0.036299] inspect: type=2000 audit(0.030:i): land=initialized audit_enabled=0 res=i [ 0.037462] hw-breakpoint: found v (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.037476] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.037798] Serial: AMBA PL011 UART driver [ 0.041354] bcm2835-mbox fe00b880.mailbox: mailbox enabled [ 0.060818] raspberrypi-firmware soc:firmware: Attached to firmware from 2020-10-22 13:59, variant start [ 0.070833] raspberrypi-firmware soc:firmware: Firmware hash is 74e754ff8947c58d2773253f77f6f68a303188f8 [ 0.126354] bcm2835-dma fe007000.dma: DMA legacy API manager, dmachans=0x1 [ 0.131456] vgaarb: loaded [ 0.131919] SCSI subsystem initialized [ 0.132139] usbcore: registered new interface commuter usbfs [ 0.132195] usbcore: registered new interface commuter hub [ 0.132328] usbcore: registered new device commuter usb [ 0.132664] usb_phy_generic phy: phy supply vcc not found, using dummy regulator [ 0.134523] clocksource: Switched to clocksource arch_sys_counter [ 0.841223] VFS: Disk quotas dquot_6.half-dozen.0 [ 0.841323] VFS: Dquot-cache hash table entries: 1024 (lodge 0, 4096 bytes) [ 0.841486] FS-Cache: Loaded [ 0.841692] CacheFiles: Loaded [ 0.851953] thermal_sys: Registered thermal governor 'step_wise' [ 0.852320] NET: Registered protocol family unit 2 [ 0.853054] tcp_listen_portaddr_hash hash table entries: 512 (guild: 0, 6144 bytes, linear) [ 0.853085] TCP established hash tabular array entries: 8192 (social club: three, 32768 bytes, linear) [ 0.853142] TCP demark hash table entries: 8192 (guild: four, 65536 bytes, linear) [ 0.853209] TCP: Hash tables configured (established 8192 bind 8192) [ 0.853358] UDP hash table entries: 512 (order: ii, 16384 bytes, linear) [ 0.853392] UDP-Light hash tabular array entries: 512 (order: 2, 16384 bytes, linear) [ 0.853641] NET: Registered protocol family unit 1 [ 0.854369] RPC: Registered named UNIX socket transport module. [ 0.854382] RPC: Registered udp transport module. [ 0.854395] RPC: Registered tcp transport module. [ 0.854408] RPC: Registered tcp NFSv4.one backchannel ship module. [ 0.854429] PCI: CLS 0 bytes, default 64 [ 0.856567] hw perfevents: enabled with armv7_cortex_a15 PMU commuter, 7 counters available [ 0.858745] Initialise system trusted keyrings [ 0.858997] workingset: timestamp_bits=xiv max_order=twenty bucket_order=half dozen [ 0.869867] FS-Enshroud: Netfs 'nfs' registered for caching [ 0.870597] NFS: Registering the id_resolver key blazon [ 0.870628] Cardinal blazon id_resolver registered [ 0.870642] Key type id_legacy registered [ 0.870665] nfs4filelayout_init: NFSv4 File Layout Commuter Registering... [ 0.871755] Cardinal blazon asymmetric registered [ 0.871769] Asymmetric key parser 'x509' registered [ 0.871963] bounce: puddle size: 64 pages [ 0.872004] Block layer SCSI generic (bsg) commuter version 0.four loaded (major 249) [ 0.872240] io scheduler mq-borderline registered [ 0.872254] io scheduler kyber registered [ 0.876286] brcm-pcie fd500000.pcie: host span /scb/pcie@7d500000 ranges: [ 0.876310] brcm-pcie fd500000.pcie: No motorcoach range found for /scb/pcie@7d500000, using [coach 00-ff] [ 0.876395] brcm-pcie fd500000.pcie: MEM 0x0600000000..0x0603ffffff -> 0x00f8000000 [ 0.876466] brcm-pcie fd500000.pcie: IB MEM 0x0000000000..0x00bfffffff -> 0x0000000000 [ 0.936645] brcm-pcie fd500000.pcie: link upwards, 5 GT/s x1 (SSC) [ 0.936967] brcm-pcie fd500000.pcie: PCI host span to passenger vehicle 0000:00 [ 0.936986] pci_bus 0000:00: root bus resource [bus 00-ff] [ 0.937006] pci_bus 0000:00: root motorbus resource [mem 0x600000000-0x603ffffff] (bus address [0xf8000000-0xfbffffff]) [ 0.937065] pci 0000:00:00.0: [14e4:2711] type 01 grade 0x060400 [ 0.937334] pci 0000:00:00.0: PME# supported from D0 D3hot [ 0.940616] PCI: bus0: Fast dorsum to dorsum transfers disabled [ 0.940849] pci 0000:01:00.0: [1106:3483] blazon 00 grade 0x0c0330 [ 0.940997] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x00000fff 64bit] [ 0.941430] pci 0000:01:00.0: PME# supported from D0 D3cold [ 0.944732] PCI: bus1: Fast back to back transfers disabled [ 0.944792] pci 0000:00:00.0: BAR 8: assigned [mem 0x600000000-0x6000fffff] [ 0.944815] pci 0000:01:00.0: BAR 0: assigned [mem 0x600000000-0x600000fff 64bit] [ 0.944897] pci 0000:00:00.0: PCI bridge to [coach 01] [ 0.944922] pci 0000:00:00.0: bridge window [mem 0x600000000-0x6000fffff] [ 0.945235] pcieport 0000:00:00.0: enabling device (0140 -> 0142) [ 0.945479] pcieport 0000:00:00.0: PME: Signaling with IRQ 55 [ 0.945878] pcieport 0000:00:00.0: AER: enabled with IRQ 55 [ 0.946224] pci 0000:01:00.0: enabling device (0140 -> 0142) [ 0.953179] iproc-rng200 fe104000.rng: hwrng registered [ 0.953511] vc-mem: phys_addr:0x00000000 mem_base=0x3ec00000 mem_size:0x40000000(1024 MiB) [ 0.954155] vc-sm: Videocore shared memory driver [ 0.954789] gpiomem-bcm2835 fe200000.gpiomem: Initialised: Registers at 0xfe200000 [ 0.966935] brd: module loaded [ 0.979242] loop: module loaded [ 0.980651] Loading iSCSI transport class v2.0-870. [ 0.982603] libphy: Fixed MDIO Bus: probed [ 0.983235] bcmgenet fd580000.ethernet: failed to get enet clock [ 0.983254] bcmgenet fd580000.ethernet: GENET 5.0 EPHY: 0x0000 [ 0.983277] bcmgenet fd580000.ethernet: failed to get enet-wol clock [ 0.983299] bcmgenet fd580000.ethernet: failed to get enet-eee clock [ 0.983325] bcmgenet: Skipping UMAC reset [ 0.994565] libphy: bcmgenet MII bus: probed [ 1.074642] unimac-mdio unimac-mdio.-19: Broadcom UniMAC MDIO motorbus [ 1.075659] usbcore: registered new interface driver r8152 [ 1.075725] usbcore: registered new interface driver lan78xx [ 1.075783] usbcore: registered new interface driver smsc95xx [ 1.076225] xhci_hcd 0000:01:00.0: xHCI Host Controller [ 1.076258] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number one [ one.078860] xhci_hcd 0000:01:00.0: hcc params 0x002841eb hci version 0x100 quirks 0x0000001000000890 [ 1.080164] usb usb1: New USB device establish, idVendor=1d6b, idProduct=0002, bcdDevice= 5.04 [ one.080182] usb usb1: New USB device strings: Mfr=iii, Production=2, SerialNumber=1 [ 1.080199] usb usb1: Product: xHCI Host Controller [ ane.080214] usb usb1: Manufacturer: Linux 5.4.72-v7l+ xhci-hcd [ 1.080229] usb usb1: SerialNumber: 0000:01:00.0 [ 1.080832] hub 1-0:ane.0: USB hub establish [ 1.080940] hub 1-0:1.0: i port detected [ one.081528] xhci_hcd 0000:01:00.0: xHCI Host Controller [ 1.081554] xhci_hcd 0000:01:00.0: new USB bus registered, assigned autobus number ii [ i.081578] xhci_hcd 0000:01:00.0: Host supports USB 3.0 SuperSpeed [ 1.082111] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= v.04 [ 1.082129] usb usb2: New USB device strings: Mfr=3, Product=ii, SerialNumber=1 [ 1.082144] usb usb2: Product: xHCI Host Controller [ 1.082159] usb usb2: Manufacturer: Linux 5.4.72-v7l+ xhci-hcd [ 1.082174] usb usb2: SerialNumber: 0000:01:00.0 [ i.082754] hub two-0:1.0: USB hub plant [ 1.082837] hub 2-0:ane.0: four ports detected [ ane.084290] dwc_otg: version 3.00a 10-AUG-2012 (platform bus) [ 1.084627] dwc_otg: FIQ enabled [ 1.084640] dwc_otg: NAK holdoff enabled [ 1.084652] dwc_otg: FIQ split-transaction FSM enabled [ one.084667] Module dwc_common_port init [ 1.085106] usbcore: registered new interface commuter uas [ ane.085209] usbcore: registered new interface commuter usb-storage [ one.085403] mousedev: PS/2 mouse device mutual for all mice [ 1.087267] bcm2835-wdt bcm2835-wdt: Broadcom BCM2835 watchdog timer [ 1.090694] sdhci: Secure Digital Host Controller Interface driver [ 1.090706] sdhci: Copyright(c) Pierre Ossman [ ane.091311] mmc-bcm2835 fe300000.mmcnr: could not get clk, deferring probe [ 1.091880] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.095699] ledtrig-cpu: registered to indicate activity on CPUs [ ane.096007] hidraw: raw HID events commuter (C) Jiri Kosina [ 1.096200] usbcore: registered new interface driver usbhid [ 1.096212] usbhid: USB HID core driver [ i.097243] vchiq: vchiq_init_state: slot_zero = (ptrval) [ ane.099171] [vc_sm_connected_init]: start [ 1.108125] [vc_sm_connected_init]: terminate - returning 0 [ 1.110355] Initializing XFRM netlink socket [ i.110394] NET: Registered protocol family 17 [ 1.110500] Key type dns_resolver registered [ 1.110946] Registering SWP/SWPB emulation handler [ 1.111253] registered taskstats version i [ ane.111272] Loading compiled-in Ten.509 certificates [ ane.111812] Primal type ._fscrypt registered [ 1.111825] Primal type .fscrypt registered [ 1.122550] uart-pl011 fe201000.serial: cts_event_workaround enabled [ 1.122622] fe201000.series: ttyAMA0 at MMIO 0xfe201000 (irq = 29, base_baud = 0) is a PL011 rev2 [ i.128720] bcm2835-ability bcm2835-power: Broadcom BCM2835 power domains commuter [ 1.129704] mmc-bcm2835 fe300000.mmcnr: mmc_debug:0 mmc_debug2:0 [ i.129720] mmc-bcm2835 fe300000.mmcnr: DMA aqueduct allocated [ 1.177770] mmc1: queuing unknown CIS tuple 0x80 (2 bytes) [ 1.179427] mmc1: queuing unknown CIS tuple 0x80 (iii bytes) [ 1.181085] mmc1: queuing unknown CIS tuple 0x80 (three bytes) [ 1.184054] mmc1: queuing unknown CIS tuple 0x80 (7 bytes) [ 1.186815] mmc1: queuing unknown CIS tuple 0x80 (3 bytes) [ 1.193163] mmc0: SDHCI controller on fe340000.emmc2 [fe340000.emmc2] using ADMA [ 1.196111] of_cfs_init [ 1.196373] of_cfs_init: OK [ one.197418] Waiting for root device PARTUUID=4a0ad747-02... [ 1.233359] random: fast init washed [ ane.257181] mmc1: new high speed SDIO bill of fare at address 0001 [ 1.299670] mmc0: new ultra loftier speed DDR50 SDHC menu at accost aaaa [ 1.300571] mmcblk0: mmc0:aaaa SL16G 14.8 GiB [ ane.303798] mmcblk0: p1 p2 [ 1.324780] EXT4-fs (mmcblk0p2): INFO: recovery required on readonly filesystem [ 1.324795] EXT4-fs (mmcblk0p2): write access will be enabled during recovery [ ane.403831] EXT4-fs (mmcblk0p2): recovery complete [ 1.405363] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null) [ ane.405437] VFS: Mounted root (ext4 filesystem) readonly on device 179:2. [ 1.406280] devtmpfs: mounted [ i.414952] Freeing unused kernel memory: 2048K [ i.415250] Run /sbin/init as init process [ 1.444581] usb i-1: new loftier-speed USB device number ii using xhci_hcd [ 1.832003] systemd[1]: Arrangement time before build time, advancing clock. [ one.923844] NET: Registered protocol family ten [ one.925311] Segment Routing with IPv6 [ ane.958433] systemd[1]: systemd 241 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN2 +IDN -PCRE2 default-bureaucracy=hybrid) [ 1.959213] systemd[ane]: Detected architecture arm. [ 2.001537] systemd[1]: Set up hostname to <raspberrypi>. [ 2.703846] random: systemd: uninitialized urandom read (xvi bytes read) [ 2.717167] random: systemd: uninitialized urandom read (xvi bytes read) [ 2.717560] systemd[1]: Listening on initctl Compatibility Named Pipe. [ two.717977] random: systemd: uninitialized urandom read (16 bytes read) [ two.720064] systemd[1]: Created slice User and Session Piece. [ 2.720221] systemd[1]: Reached target Slices. [ ii.721290] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Indicate. [ ii.723561] systemd[one]: Created slice system-getty.piece. [ 2.724197] systemd[ane]: Listening on fsck to fsckd communication Socket. [ 2.724947] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ two.820767] i2c /dev entries driver [ 3.328725] EXT4-fs (mmcblk0p2): re-mounted. Opts: (nada) [ iii.414082] systemd-journald[116]: Received request to flush runtime periodical from PID one [ 4.012761] rpivid-mem feb00000.hevc-decoder: rpivid-hevcmem initialised: Registers at 0xfeb00000 length 0x00010000 [ 4.013194] rpivid-mem feb10000.rpivid-local-intc: rpivid-intcmem initialised: Registers at 0xfeb10000 length 0x00001000 [ four.013619] rpivid-mem feb20000.h264-decoder: rpivid-h264mem initialised: Registers at 0xfeb20000 length 0x00010000 [ 4.014035] rpivid-mem feb30000.vp9-decoder: rpivid-vp9mem initialised: Registers at 0xfeb30000 length 0x00010000 [ 4.078654] vc_sm_cma: module is from the staging directory, the quality is unknown, you have been warned. [ 4.080659] bcm2835_vc_sm_cma_probe: Videocore shared memory commuter [ four.080687] [vc_sm_connected_init]: start [ 4.102150] [vc_sm_connected_init]: installed successfully [ iv.102500] mc: Linux media interface: v0.ten [ iv.138371] videodev: Linux video capture interface: v2.00 [ 4.142472] snd_bcm2835: module is from the staging directory, the quality is unknown, you have been warned. [ 4.175090] bcm2835_audio bcm2835_audio: card created with 8 channels [ 4.190552] bcm2835_mmal_vchiq: module is from the staging directory, the quality is unknown, yous have been warned. [ 4.214696] bcm2835_v4l2: module is from the staging directory, the quality is unknown, you have been warned. [ iv.217571] bcm2835_isp: module is from the staging directory, the quality is unknown, you have been warned. [ 4.277799] bcm2835-internet service provider bcm2835-isp: Device node output[0] registered every bit /dev/video13 [ 4.281417] bcm2835-isp bcm2835-internet access provider: Device node capture[0] registered equally /dev/video14 [ iv.285453] bcm2835-isp bcm2835-isp: Device node capture[1] registered equally /dev/video15 [ 4.285926] bcm2835-isp bcm2835-internet service provider: Device node stats[2] registered as /dev/video16 [ iv.285958] bcm2835-isp bcm2835-internet service provider: Register output node 0 with media controller [ iv.285988] bcm2835-isp bcm2835-internet access provider: Register capture node i with media controller [ 4.286017] bcm2835-isp bcm2835-isp: Annals capture node 2 with media controller [ iv.286042] bcm2835-isp bcm2835-isp: Register capture node 3 with media controller [ 4.288994] bcm2835-internet access provider bcm2835-isp: Loaded V4L2 bcm2835-internet service provider [ 4.301701] bcm2835_codec: module is from the staging directory, the quality is unknown, y'all take been warned. [ iv.334958] bcm2835-codec bcm2835-codec: Device registered as /dev/video10 [ 4.335005] bcm2835-codec bcm2835-codec: Loaded V4L2 decode [ 4.341913] bcm2835-codec bcm2835-codec: Device registered every bit /dev/video11 [ iv.341953] bcm2835-codec bcm2835-codec: Loaded V4L2 encode [ 4.358931] bcm2835-codec bcm2835-codec: Device registered as /dev/video12 [ iv.358975] bcm2835-codec bcm2835-codec: Loaded V4L2 internet access provider [ 4.362947] cfg80211: Loading compiled-in X.509 certificates for regulatory database [ 4.461118] [drm] Initialized v3d one.0.0 20180419 for fec00000.v3d on minor 0 [ 4.509954] cfg80211: Loaded 10.509 cert 'sforshee: 00b28ddf47aef9cea7' [ 4.580752] brcmfmac: F1 signature read @0x18000000=0x15264345 [ 4.597531] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43455-sdio for chip BCM4345/6 [ iv.598499] usbcore: registered new interface commuter brcmfmac [ four.623921] brcmfmac mmc1:0001:1: Straight firmware load for brcm/brcmfmac43455-sdio.raspberrypi,4-model-b.txt failed with error -2 [ iv.664237] [drm] No displays found. Consider forcing hotplug if HDMI is attached [ iv.664360] vc4-drm gpu: jump fe600000.firmwarekms (ops vc4_fkms_ops [vc4]) [ four.664385] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). [ 4.664398] [drm] No driver support for vblank timestamp query. [ 4.664411] [drm] Setting vblank_disable_immediate to fake because get_vblank_timestamp == Zilch [ iv.675261] [drm] Initialized vc4 0.0.0 20140616 for gpu on minor 1 [ 4.870926] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43455-sdio for fleck BCM4345/6 [ iv.887354] brcmfmac: brcmf_c_preinit_dcmds: Firmware: BCM4345/6 wl0: Mar 23 2022 02:xix:54 version seven.45.206 (r725000 CY) FWID 01-88ee44ea [ 6.626884] usb one-1: device descriptor read/64, fault -110 [ 6.738361] random: crng init washed [ 6.738379] random: seven urandom warning(s) missed due to ratelimiting [ half dozen.793293] uart-pl011 fe201000.serial: no DMA platform data [ 6.867815] 8021q: 802.1Q VLAN Support v1.viii [ 7.285879] Adding 102396k swap on /var/swap. Priority:-2 extents:one beyond:102396k SSFS [ 7.309444] brcmfmac: brcmf_cfg80211_set_power_mgmt: power save enabled [ seven.546155] bcmgenet: Skipping UMAC reset [ 7.547723] bcmgenet fd580000.ethernet: configuring instance for external RGMII [ 7.547928] bcmgenet fd580000.ethernet eth0: Link is Down [ ix.119002] cleaved atomic modeset userspace detected, disabling atomic [ 9.814334] broken atomic modeset userspace detected, disabling atomic [ ten.846877] broken atomic modeset userspace detected, disabling atomic [ 11.449159] broken atomic modeset userspace detected, disabling atomic [ 12.489251] broken atomic modeset userspace detected, disabling diminutive [ 12.715836] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes fix [ xiii.112854] cleaved atomic modeset userspace detected, disabling atomic [ 13.473196] Bluetooth: Core ver 2.22 [ 13.474122] NET: Registered protocol family 31 [ 13.474128] Bluetooth: HCI device and connection director initialized [ 13.474141] Bluetooth: HCI socket layer initialized [ thirteen.474149] Bluetooth: L2CAP socket layer initialized [ 13.474164] Bluetooth: SCO socket layer initialized [ 13.484855] Bluetooth: HCI UART commuter ver 2.iii [ xiii.484864] Bluetooth: HCI UART protocol H4 registered [ 13.484902] Bluetooth: HCI UART protocol Three-wire (H5) registered [ thirteen.485053] Bluetooth: HCI UART protocol Broadcom registered [ 13.707304] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ thirteen.707312] Bluetooth: BNEP filters: protocol multicast [ xiii.707327] Bluetooth: BNEP socket layer initialized [ 13.744542] Bluetooth: RFCOMM TTY layer initialized [ xiii.744557] Bluetooth: RFCOMM socket layer initialized [ 13.744576] Bluetooth: RFCOMM ver 1.11 [ 14.188214] broken atomic modeset userspace detected, disabling atomic [ fourteen.778458] cleaved atomic modeset userspace detected, disabling atomic [ 15.821568] broken atomic modeset userspace detected, disabling atomic [ 16.383976] cleaved diminutive modeset userspace detected, disabling atomic [ 21.984803] usb one-1: device descriptor read/64, error -110 [ 22.254578] usb 1-1: new high-speed USB device number 3 using xhci_hcd [ 27.424802] usb 1-one: device descriptor read/64, mistake -110 [ 42.784813] usb 1-i: device descriptor read/64, error -110 [ 42.904959] usb usb1-port1: attempt power cycle [ 43.614569] usb one-1: new high-speed USB device number iv using xhci_hcd [ 48.714854] usb 1-1: device descriptor read/viii, error -110 [ 53.914761] usb one-1: device descriptor read/eight, error -110 [ 54.184579] usb 1-ane: new loftier-speed USB device number 5 using xhci_hcd [ 59.274753] usb one-i: device descriptor read/8, error -110 [ 64.474801] usb 1-1: device descriptor read/all, error -110 [ 64.475191] usb usb1-port1: unable to enumerate USB deviceAlles anzeigen
System wurde geupdatet
Linux raspberrypi five.iv.72-v7l+ #1356 SMP Thu Oct 22 xiii:57:51 BST 2022 armv7l GNU/Linux pi@raspberrypi:~ $ sudo rpi-eeprom-update BCM2711 detected Dedicated VL805 EEPROM detected BOOTLOADER: upwardly-to-date Electric current: Thu iii Sep 12:11:43 UTC 2022 (1599135103) LATEST: Thu 3 Sep 12:xi:43 UTC 2022 (1599135103) FW DIR: /lib/firmware/raspberrypi/bootloader/stable VL805: upwardly-to-engagement Electric current: 000138a1 LATEST: 000138a1 pi@raspberrypi:~ $ vcgencmd bootloader_version Sep 3 2022 xiii:xi:43 version c305221a6d7e532693cc7ff57fddfc8649def167 (release) timestamp 1599135103Alles anzeigen
Infos zu USB
pi@raspberrypi:~/uhub/uhubctl $ sudo lsusb -t /: Charabanc 02.Port one: Dev 1, Grade=root_hub, Commuter=xhci_hcd/4p, 5000M /: Motorbus 01.Port i: Dev 1, Class=root_hub, Commuter=xhci_hcd/1p, 480M pi@raspberrypi:~/uhub/uhubctl $ sudo lsusb -v Double-decker 002 Device 001: ID 1d6b:0003 Linux Foundation iii.0 root hub Device Descriptor: bLength xviii bDescriptorType i bcdUSB iii.00 bDeviceClass 9 Hub bDeviceSubClass 0 bDeviceProtocol three bMaxPacketSize0 ix idVendor 0x1d6b Linux Foundation idProduct 0x0003 3.0 root hub bcdDevice 5.04 iManufacturer 3 Linux 5.four.72-v7l+ xhci-hcd iProduct ii xHCI Host Controller iSerial 1 0000:01:00.0 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 0x001f bNumInterfaces one bConfigurationValue 1 iConfiguration 0 bmAttributes 0xe0 Cocky Powered Remote Wakeup MaxPower 0mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 1 bInterfaceClass nine Hub bInterfaceSubClass 0 bInterfaceProtocol 0 Total speed (or root) hub iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP one IN bmAttributes 3 Transfer Type Interrupt Synch Blazon None Usage Type Data wMaxPacketSize 0x0004 1x iv bytes bInterval 12 bMaxBurst 0 Hub Descriptor: bLength 12 bDescriptorType 42 nNbrPorts 4 wHubCharacteristic 0x0009 Per-port power switching Per-port overcurrent protection bPwrOn2PwrGood 10 * ii milli seconds bHubContrCurrent 0 milli Ampere bHubDecLat 0.0 micro seconds wHubDelay 0 nano seconds DeviceRemovable 0x00 Hub Port Status: Port 1: 0000.02a0 5Gbps power Rx.Discover Port 2: 0000.02a0 5Gbps ability Rx.Detect Port iii: 0000.02a0 5Gbps power Rx.Detect Port 4: 0000.02a0 5Gbps ability Rx.Detect Binary Object Store Descriptor: bLength five bDescriptorType 15 wTotalLength 0x000f bNumDeviceCaps ane SuperSpeed USB Device Capability: bLength 10 bDescriptorType 16 bDevCapabilityType 3 bmAttributes 0x02 Latency Tolerance Messages (LTM) Supported wSpeedsSupported 0x0008 Device can operate at SuperSpeed (5Gbps) bFunctionalitySupport 3 Everyman fully-functional device speed is SuperSpeed (5Gbps) bU1DevExitLat iv micro seconds bU2DevExitLat 231 micro seconds tin can't go debug descriptor: Resource temporarily unavailable Device Status: 0x0001 Self Powered Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Device Descriptor: bLength eighteen bDescriptorType 1 bcdUSB two.00 bDeviceClass 9 Hub bDeviceSubClass 0 bDeviceProtocol 1 Single TT bMaxPacketSize0 64 idVendor 0x1d6b Linux Foundation idProduct 0x0002 2.0 root hub bcdDevice five.04 iManufacturer 3 Linux five.4.72-v7l+ xhci-hcd iProduct two xHCI Host Controller iSerial one 0000:01:00.0 bNumConfigurations 1 Configuration Descriptor: bLength ix bDescriptorType 2 wTotalLength 0x0019 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0xe0 Self Powered Remote Wakeup MaxPower 0mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 1 bInterfaceClass 9 Hub bInterfaceSubClass 0 bInterfaceProtocol 0 Full speed (or root) hub iInterface 0 Endpoint Descriptor: bLength seven bDescriptorType 5 bEndpointAddress 0x81 EP ane IN bmAttributes three Transfer Type Interrupt Synch Type None Usage Type Information wMaxPacketSize 0x0004 1x iv bytes bInterval 12 Hub Descriptor: bLength 9 bDescriptorType 41 nNbrPorts 1 wHubCharacteristic 0x0009 Per-port ability switching Per-port overcurrent protection TT think fourth dimension 8 FS bits bPwrOn2PwrGood ten * 2 milli seconds bHubContrCurrent 0 milli Ampere DeviceRemovable 0x02 PortPwrCtrlMask 0xff Hub Port Status: Port one: 0000.0501 highspeed ability connect can't go device qualifier: Resource temporarily unavailable tin can't get debug descriptor: Resource temporarily unavailable Device Status: 0x0001 Self PoweredAlles anzeigen
Gerade eben gezogene Infos: aus /sys/double-decker/usb/devices/usb1 power/runtime_suspended_time:1199086 ability/runtime_status:suspended power/runtime_active_time:42942 ability/level:motorcar power/control:auto power/connected_duration:1242030 ability/autosuspend_delay_ms:0 power/autosuspend:0 power/active_duration:42940 aus /sys/motorcoach/usb/devices/usb2 power/runtime_suspended_time:1320794 power/runtime_status:suspended power/runtime_active_time:103 power/level:automobile power/command:machine power/connected_duration:1320900 power/autosuspend_delay_ms:0 ability/autosuspend:0 ability/active_duration:110Alles anzeigen
Die Ports sind scheinbar aus.
Versuch mit uhubctl (https://github.com/mvp/uhubctl) etwas zu aktivieren
pi@raspberrypi:~/uhub/uhubctl $ sudo ./uhubctl -a on -p 1 Electric current condition for hub two [1d6b:0003 Linux v.four.72-v7l+ xhci-hcd xHCI Host Controller 0000:01:00.0, USB three.00, 4 ports] Port ane: 02a0 ability 5gbps Rx.Detect Sent power on request New status for hub ii [1d6b:0003 Linux v.4.72-v7l+ xhci-hcd xHCI Host Controller 0000:01:00.0, USB three.00, 4 ports] Port i: 02a0 ability 5gbps Rx.Detect Current status for hub 1 [1d6b:0002 Linux 5.4.72-v7l+ xhci-hcd xHCI Host Controller 0000:01:00.0] Port 1: 0501 ability highspeed connect [] Sent power on asking New status for hub ane [1d6b:0002 Linux 5.4.72-v7l+ xhci-hcd xHCI Host Controller 0000:01:00.0] Port 1: 0501 ability highspeed connect []Alles anzeigen
und der dazugehörige Abschnitt aus dmesg
[ 573.368707] usb 1-ane: new high-speed USB device number 6 using xhci_hcd [ 578.548969] usb 1-1: device descriptor read/64, fault -110 [ 593.909113] usb 1-one: device descriptor read/64, error -110 [ 594.178865] usb one-1: new high-speed USB device number seven using xhci_hcd [ 599.349160] usb 1-1: device descriptor read/64, error -110 [ 614.709285] usb 1-one: device descriptor read/64, error -110 [ 614.829421] usb usb1-port1: attempt power cycle [ 615.539035] usb ane-1: new high-speed USB device number 8 using xhci_hcd [ 620.639355] usb 1-ane: device descriptor read/8, error -110 [ 625.839359] usb 1-1: device descriptor read/8, error -110 [ 626.109120] usb 1-ane: new high-speed USB device number 9 using xhci_hcd [ 631.199446] usb ane-one: device descriptor read/8, error -110 [ 636.399388] usb one-i: device descriptor read/8, error -110 [ 636.519602] usb usb1-port1: unable to enumerate USB device [ 636.699208] usb one-i: new high-speed USB device number x using xhci_hcd [ 641.909500] usb 1-1: device descriptor read/64, error -110 [ 657.270084] usb 1-ane: device descriptor read/64, fault -110 [ 657.539871] usb 1-1: new high-speed USB device number 11 using xhci_hcd [ 662.710383] usb 1-1: device descriptor read/64, error -110 [ 678.081029] usb 1-1: device descriptor read/all, error -110 [ 678.081406] usb usb1-port1: try power cycle [ 678.790836] usb 1-ane: new high-speed USB device number 12 using xhci_hcd [ 683.841281] usb ane-one: device descriptor read/viii, error -110 [ 689.041410] usb 1-1: device descriptor read/eight, mistake -110 [ 689.311240] usb 1-1: new high-speed USB device number 13 using xhci_hcd [ 694.401682] usb 1-1: device descriptor read/8, mistake -110 [ 699.601840] usb 1-i: device descriptor read/all, error -110 [ 699.602223] usb usb1-port1: unable to enumerate USB deviceAlles anzeigen
Und weil dumme Jungs dumme Dinge tun habe ich auch mal ein rpi-update laufen lassen. Danach alles unverändert...
pi@raspberrypi:~ $ sudo rpi-update *** Raspberry Pi firmware updater by Hexxeh, enhanced past AndrewS and Dom *** Performing self-update *** Relaunching subsequently update *** Raspberry Pi firmware updater by Hexxeh, enhanced by AndrewS and Dom *** We're running for the first fourth dimension *** Bankroll up files (this will take a few minutes) *** Backing upwards firmware *** Backing up modules 5.4.72-v7l+ ############################################################# WARNING: This update bumps to rpi-v.iv.y linux tree See: https://www.raspberrypi.org/forums/viewtopic.php?f=29&t=269769 'rpi-update' should merely exist used if in that location is a specific reason to do and so - for example, a request by a Raspberry Pi engineer or if you want to assist the testing effort and are comfy with restoring if there are regressions. Do Not employ 'rpi-update' equally part of a regular update procedure. ############################################################## Would you lot similar to go along? (y/N) *** Downloading specific firmware revision (this volition take a few minutes) % Full % Received % Xferd Average Speed Time Fourth dimension Fourth dimension Electric current Dload Upload Total Spent Left Speed 100 168 100 168 0 0 1631 0 --:--:-- --:--:-- --:--:-- 1647 100 117M 0 117M 0 0 4139k 0 --:--:-- 0:00:29 --:--:-- 2737k *** Updating firmware *** Updating kernel modules *** depmod 5.4.77-v7+ *** depmod five.4.77+ *** depmod 5.4.77-v8+ *** depmod 5.four.77-v7l+ *** Updating VideoCore libraries *** Using HardFP libraries *** Updating SDK *** Running ldconfig *** Storing current firmware revision *** Deleting downloaded files *** Syncing changes to deejay *** If no errors appeared, your firmware was successfully updated to ab9d6874ff67f7ef015d04358ad1e7711abe3f20 *** A reboot is needed to actuate the new firmware pi@raspberrypi:~ $Alles anzeigen
Für Tipps wäre ich dankbar
-
- #2
Und wenn du Raspbian Bone auf die Karte flashst, statt mit NOOBS ?
Ist NOOBS jetzt Geschichte?
-
- #iii
Ich habe einen neuen Raspberry Pi 4 aus einem Kit von Berrybase
Infos zu USB
pi@raspberrypi:~/uhub/uhubctl $ sudo lsusb -t /: Bus 02.Port one: Dev i, Form=root_hub, Driver=xhci_hcd/4p, 5000M /: Jitney 01.Port i: Dev 1, Class=root_hub, Driver=xhci_hcd/1p, 480MDie Ports sind scheinbar aus.
Auf meinem PI4 ist die Ausgabe so:
:~# lsusb -t /: Bus 02.Port 1: Dev i, Class=root_hub, Driver=xhci_hcd/4p, 5000M /: Bus 01.Port one: Dev one, Class=root_hub, Driver=xhci_hcd/1p, 480M |__ Port one: Dev 2, If 0, Class=Hub, Commuter=hub/4p, 480M:~# lsusb Bus 002 Device 001: ID 1d6b:0003 Linux Foundation three.0 root hub Autobus 001 Device 002: ID 2109:3431 VIA Labs, Inc. Hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub -
- #4
Und wenn du Raspbian OS auf die Karte flashst, statt mit NOOBS ?
Ist NOOBS jetzt Geschichte?
Habe ich gemacht, oben steht mit Raspberry Imager.
Ich hatt eNoobs verwendet, weil es schon auf der mitgelieferten SD Karte drauf war und ich nicht wusste, dass es "Geschichte" ist.
Aber ein ganz guter Punkt, um zu sehen, dass ja doch nicht alle sim Eimer ist mit meinem Rapsberry.
Auf meinem PI4 ist die Ausgabe so:
:~# lsusb -t /: Motorbus 02.Port 1: Dev i, Class=root_hub, Commuter=xhci_hcd/4p, 5000M /: Bus 01.Port 1: Dev 1, Class=root_hub, Driver=xhci_hcd/1p, 480M |__ Port 1: Dev ii, If 0, Class=Hub, Driver=hub/4p, 480M:~# lsusb Omnibus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 001 Device 002: ID 2109:3431 VIA Labs, Inc. Hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hubHast du irgendwas dranhängen an den Ports?
-
- #v
Hast du irgendwas dranhängen an den Ports?
Nein.
Poste mal nach einem:
echo i > /sys/bus/pci/devices/0000\:01\:00.0/remove(... damit werden dice USB-Anschlüsse deaktiviert), die Ausgabe von:
-
- #six
dmesg von Noobs, also kein Hardwareproblem und auch nciht die Stromversorgung
[ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.4.51-rescue-v7l (serge@buildbot) (gcc version four.viii.4 (Buildroot 2015.02-git-00125-g0082207-dirty)) #2 SMP Tue Sep 15 ten:48:x BST 2020 [ 0.000000] CPU: ARMv7 Processor [410fd083] revision three (ARMv7), cr=30c5383d [ 0.000000] CPU: div instructions bachelor: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Automobile model: Raspberry Pi 4 Model B Rev i.two [ 0.000000] Memory policy: Data enshroud writealloc [ 0.000000] Reserved memory: created CMA retentivity puddle at 0x0000000029400000, size 64 MiB [ 0.000000] OF: reserved mem: initialized node linux,cma, compatible id shared-dma-pool [ 0.000000] On node 0 totalpages: 1025536 [ 0.000000] DMA zone: 1920 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 196608 pages, LIFO batch:63 [ 0.000000] HighMem zone: 828928 pages, LIFO batch:63 [ 0.000000] percpu: Embedded 13 pages/cpu s30144 r0 d23104 u53248 [ 0.000000] pcpu-alloc: s30144 r0 d23104 u53248 alloc=xiii*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] one [0] 2 [0] 3 [ 0.000000] Congenital ane zonelists, mobility group on. Total pages: 1023616 [ 0.000000] Kernel command line: coherent_pool=1M 8250.nr_uarts=0 snd_bcm2835.enable_compat_alsa=0 snd_bcm2835.enable_hdmi=1 snd_bcm2835.enable_headphones=one bcm2708_fb.fbwidth=1824 bcm2708_fb.fbheight=984 bcm2708_fb.fbdepth=16 bcm2708_fb.fbswap=1 smsc95xx.macaddr=DC:A6:32:B7:58:F6 vc_mem.mem_base=0x3f000000 vc_mem.mem_size=0x3f600000 quiet ramdisk_size=32768 root=/dev/ram0 init=/init vt.cur_default=ane elevator=deadline sdhci.debug_quirks2=4 [ 0.000000] Dentry enshroud hash table entries: 131072 (order: 7, 524288 bytes, linear) [ 0.000000] Inode-cache hash tabular array entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] software IO TLB: mapped [mem 0x22ca0000-0x26ca0000] (64MB) [ 0.000000] Memory: 3890068K/4102144K available (6144K kernel code, 165K rwdata, 1108K rodata, 2048K init, 494K bss, 146540K reserved, 65536K cma-reserved, 3315712K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=one [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment filibuster is 10 jiffies. [ 0.000000] NR_IRQS: 16, nr_irqs: xvi, preallocated irqs: 16 [ 0.000000] GIC: Using split EOI/Deactivate mode [ 0.000000] random: get_random_bytes chosen from start_kernel+0x2c8/0x464 with crng_init=0 [ 0.000007] sched_clock: 32 bits at 1000kHz, resolution 1000ns, wraps every 2147483647500ns [ 0.000021] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275 ns [ 0.000087] bcm2835: organisation timer (irq = 17) [ 0.000625] arch_timer: cp15 timer(s) running at 54.00MHz (phys). [ 0.000639] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0xc743ce346, max_idle_ns: 440795203123 ns [ 0.000654] sched_clock: 56 bits at 54MHz, resolution 18ns, wraps every 4398046511102ns [ 0.000666] Switching to timer-based delay loop, resolution 18ns [ 0.000823] Panel: colour dummy device 80x30 [ 0.000840] printk: console [tty0] enabled [ 0.000865] Calibrating delay loop (skipped), value calculated using timer frequency.. 108.00 BogoMIPS (lpj=540000) [ 0.000877] pid_max: default: 32768 minimum: 301 [ 0.000995] Mount-enshroud hash table entries: 2048 (order: i, 8192 bytes, linear) [ 0.001011] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.001551] CPU: Testing write buffer coherency: ok [ 0.001794] CPU0: thread -i, cpu 0, socket 0, mpidr 80000000 [ 0.002171] Setting upwards static identity map for 0x200000 - 0x20003c [ 0.002250] rcu: Hierarchical SRCU implementation. [ 0.002512] smp: Bringing up secondary CPUs ... [ 0.003032] CPU1: thread -1, cpu i, socket 0, mpidr 80000001 [ 0.003629] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 [ 0.004209] CPU3: thread -i, cpu 3, socket 0, mpidr 80000003 [ 0.004296] smp: Brought up 1 node, 4 CPUs [ 0.004305] SMP: Total of 4 processors activated (432.00 BogoMIPS). [ 0.004312] CPU: All CPU(s) started in HYP mode. [ 0.004317] CPU: Virtualization extensions available. [ 0.004776] devtmpfs: initialized [ 0.013619] VFP support v0.3: implementor 41 architecture iii role 40 variant 8 rev 0 [ 0.013772] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.013788] futex hash tabular array entries: 1024 (guild: 4, 65536 bytes, linear) [ 0.015347] pinctrl core: initialized pinctrl subsystem [ 0.015828] NET: Registered protocol family 16 [ 0.017950] DMA: preallocated 1024 KiB puddle for atomic coherent allocations [ 0.018593] cpuidle: using governor menu [ 0.019181] Serial: AMBA PL011 UART commuter [ 0.020524] bcm2835-mbox fe00b880.mailbox: mailbox enabled [ 0.040634] raspberrypi-firmware soc:firmware: Attached to firmware from 2020-09-02 21:13, variant start_cd [ 0.050632] raspberrypi-firmware soc:firmware: Firmware hash is 4439d2aaa6c376a2d1ef4402f142e1cf4de37c43 [ 0.083760] bcm2835-dma fe007000.dma: DMA legacy API manager, dmachans=0x1 [ 0.085715] vgaarb: loaded [ 0.085967] SCSI subsystem initialized [ 0.086088] usbcore: registered new interface commuter usbfs [ 0.086117] usbcore: registered new interface commuter hub [ 0.086179] usbcore: registered new device driver usb [ 0.087100] clocksource: Switched to clocksource arch_sys_counter [ 0.087295] FS-Cache: Loaded [ 0.087393] CacheFiles: Loaded [ 0.093263] thermal_sys: Registered thermal governor 'step_wise' [ 0.093504] Net: Registered protocol family 2 [ 0.093914] tcp_listen_portaddr_hash hash table entries: 512 (gild: 0, 6144 bytes, linear) [ 0.093931] TCP established hash table entries: 8192 (gild: 3, 32768 bytes, linear) [ 0.093994] TCP bind hash tabular array entries: 8192 (social club: 4, 65536 bytes, linear) [ 0.094061] TCP: Hash tables configured (established 8192 demark 8192) [ 0.094151] UDP hash table entries: 512 (lodge: 2, 16384 bytes, linear) [ 0.094175] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) [ 0.094296] Net: Registered protocol family 1 [ 0.094610] PCI: CLS 0 bytes, default 64 [ 0.094757] Trying to unpack rootfs image as initramfs... [ 0.094926] rootfs paradigm is not initramfs (invalid magic at beginning of compressed archive); looks similar an initrd [ 0.184201] Freeing initrd memory: 28316K [ 0.185140] Initialise system trusted keyrings [ 0.185279] workingset: timestamp_bits=30 max_order=20 bucket_order=0 [ 0.190063] squashfs: version iv.0 (2009/01/31) Phillip Lougher [ 0.190192] fuse: init (API version 7.31) [ 0.190667] Key type asymmetric registered [ 0.190675] Asymmetric fundamental parser 'x509' registered [ 0.190732] bounce: pool size: 64 pages [ 0.190745] io scheduler mq-deadline registered [ 0.190752] io scheduler kyber registered [ 0.192375] brcm-pcie fd500000.pcie: host span /scb/pcie@7d500000 ranges: [ 0.192389] brcm-pcie fd500000.pcie: No bus range institute for /scb/pcie@7d500000, using [motorbus 00-ff] [ 0.192415] brcm-pcie fd500000.pcie: MEM 0x0600000000..0x0603ffffff -> 0x00f8000000 [ 0.192439] brcm-pcie fd500000.pcie: IB MEM 0x0000000000..0x00bfffffff -> 0x0000000000 [ 0.249185] brcm-pcie fd500000.pcie: link up, v GT/s x1 (SSC) [ 0.249343] brcm-pcie fd500000.pcie: PCI host bridge to bus 0000:00 [ 0.249354] pci_bus 0000:00: root jitney resources [bus 00-ff] [ 0.249367] pci_bus 0000:00: root bus resource [mem 0x600000000-0x603ffffff] (bus address [0xf8000000-0xfbffffff]) [ 0.249398] pci 0000:00:00.0: [14e4:2711] type 01 form 0x060400 [ 0.249492] pci 0000:00:00.0: PME# supported from D0 D3hot [ 0.252116] PCI: bus0: Fast back to back transfers disabled [ 0.252271] pci 0000:01:00.0: [1106:3483] type 00 course 0x0c0330 [ 0.252377] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x00000fff 64bit] [ 0.252639] pci 0000:01:00.0: PME# supported from D0 D3cold [ 0.255289] PCI: bus1: Fast back to dorsum transfers disabled [ 0.255323] pci 0000:00:00.0: BAR 8: assigned [mem 0x600000000-0x6000fffff] [ 0.255338] pci 0000:01:00.0: BAR 0: assigned [mem 0x600000000-0x600000fff 64bit] [ 0.255398] pci 0000:00:00.0: PCI span to [bus 01] [ 0.255410] pci 0000:00:00.0: bridge window [mem 0x600000000-0x6000fffff] [ 0.255480] pci 0000:00:00.0: enabling device (0140 -> 0142) [ 0.255523] pci 0000:01:00.0: enabling device (0140 -> 0142) [ 0.255882] bcm2708_fb soc:fb: FB institute 1 brandish(s) [ 0.274695] Console: switching to colour frame buffer device 228x61 [ 0.280730] bcm2708_fb soc:fb: Registered framebuffer for brandish 0, size 1824x984 [ 0.282831] vc-mem: phys_addr:0x00000000 mem_base=0x3f000000 mem_size:0x3f600000(1014 MiB) [ 0.283119] gpiomem-bcm2835 fe200000.gpiomem: Initialised: Registers at 0xfe200000 [ 0.289626] brd: module loaded [ 0.293992] loop: module loaded [ 0.295537] libphy: Fixed MDIO Bus: probed [ 0.295789] bcmgenet fd580000.ethernet: failed to get enet clock [ 0.295802] bcmgenet fd580000.ethernet: GENET v.0 EPHY: 0x0000 [ 0.295813] bcmgenet fd580000.ethernet: failed to get enet-wol clock [ 0.295824] bcmgenet fd580000.ethernet: failed to get enet-eee clock [ 0.295842] bcmgenet: Skipping UMAC reset [ 0.307114] libphy: bcmgenet MII jitney: probed [ 0.387147] unimac-mdio unimac-mdio.-nineteen: Broadcom UniMAC MDIO jitney [ 0.387913] usbcore: registered new interface driver brcmfmac [ 0.387946] usbcore: registered new interface driver r8152 [ 0.387972] usbcore: registered new interface driver lan78xx [ 0.388005] usbcore: registered new interface driver asix [ 0.388032] usbcore: registered new interface driver smsc95xx [ 0.388298] xhci_hcd 0000:01:00.0: xHCI Host Controller [ 0.388322] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number one [ 0.389739] xhci_hcd 0000:01:00.0: hcc params 0x002841eb hci version 0x100 quirks 0x0000001000000890 [ 0.390149] usb usb1: New USB device plant, idVendor=1d6b, idProduct=0002, bcdDevice= v.04 [ 0.390160] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=i [ 0.390169] usb usb1: Product: xHCI Host Controller [ 0.390177] usb usb1: Manufacturer: Linux 5.4.51-rescue-v7l xhci-hcd [ 0.390185] usb usb1: SerialNumber: 0000:01:00.0 [ 0.390604] hub i-0:1.0: USB hub found [ 0.390665] hub 1-0:1.0: 1 port detected [ 0.391018] xhci_hcd 0000:01:00.0: xHCI Host Controller [ 0.391036] xhci_hcd 0000:01:00.0: new USB jitney registered, assigned motorbus number ii [ 0.391050] xhci_hcd 0000:01:00.0: Host supports USB 3.0 SuperSpeed [ 0.391297] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.04 [ 0.391307] usb usb2: New USB device strings: Mfr=3, Product=two, SerialNumber=1 [ 0.391315] usb usb2: Production: xHCI Host Controller [ 0.391323] usb usb2: Manufacturer: Linux 5.4.51-rescue-v7l xhci-hcd [ 0.391331] usb usb2: SerialNumber: 0000:01:00.0 [ 0.391694] hub ii-0:ane.0: USB hub found [ 0.391730] hub 2-0:1.0: 4 ports detected [ 0.392555] dwc_otg: version three.00a 10-AUG-2012 (platform bus) [ 0.392647] dwc_otg: FIQ enabled [ 0.392653] dwc_otg: NAK holdoff enabled [ 0.392659] dwc_otg: FIQ dissever-transaction FSM enabled [ 0.392667] Module dwc_common_port init [ 0.392911] usbcore: registered new interface commuter uas [ 0.392964] usbcore: registered new interface commuter usb-storage [ 0.393092] mousedev: PS/2 mouse device common for all mice [ 0.393636] bcm2835-wdt bcm2835-wdt: Broadcom BCM2835 watchdog timer [ 0.398312] sdhci: Secure Digital Host Controller Interface driver [ 0.398314] sdhci: Copyright(c) Pierre Ossman [ 0.398444] mmc-bcm2835 fe300000.mmcnr: could not get clk, deferring probe [ 0.398533] sdhci-pltfm: SDHCI platform and OF commuter helper [ 0.400273] hidraw: raw HID events commuter (C) Jiri Kosina [ 0.400478] usbcore: registered new interface commuter usbhid [ 0.400481] usbhid: USB HID core commuter [ 0.400790] vchiq: vchiq_init_state: slot_zero = (ptrval) [ 0.402036] Net: Registered protocol family 17 [ 0.402186] Registering SWP/SWPB emulation handler [ 0.402231] Loading compiled-in Ten.509 certificates [ 0.402934] uart-pl011 fe201000.serial: cts_event_workaround enabled [ 0.402957] fe201000.serial: ttyAMA0 at MMIO 0xfe201000 (irq = 29, base_baud = 0) is a PL011 rev2 [ 0.406291] bcm2835-power bcm2835-ability: Broadcom BCM2835 power domains driver [ 0.406468] mmc-bcm2835 fe300000.mmcnr: mmc_debug:0 mmc_debug2:0 [ 0.406472] mmc-bcm2835 fe300000.mmcnr: DMA channel allocated [ 0.452818] mmc1: queuing unknown CIS tuple 0x80 (2 bytes) [ 0.454297] mmc1: queuing unknown CIS tuple 0x80 (3 bytes) [ 0.455774] mmc1: queuing unknown CIS tuple 0x80 (3 bytes) [ 0.458440] mmc1: queuing unknown CIS tuple 0x80 (7 bytes) [ 0.459922] mmc1: queuing unknown CIS tuple 0x80 (3 bytes) [ 0.469323] mmc0: SDHCI controller on fe340000.emmc2 [fe340000.emmc2] using ADMA [ 0.469468] cfg80211: Loading compiled-in 10.509 certificates for regulatory database [ 0.470325] cfg80211: Loaded 10.509 cert 'sforshee: 00b28ddf47aef9cea7' [ 0.470397] platform regulatory.0: Directly firmware load for regulatory.db failed with error -2 [ 0.470402] platform regulatory.0: Falling dorsum to sysfs fallback for: regulatory.db [ 0.470619] RAMDISK: squashfs filesystem found at cake 0 [ 0.470625] RAMDISK: Loading 28315KiB [1 disk] into ram disk... |/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\| [ 0.502366] random: fast init washed [ 0.502457] /-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/- [ 0.515498] mmc0: new high speed SDHC card at address aaaa [ 0.515865] mmcblk0: mmc0:aaaa SC32G 29.7 GiB [ 0.516477] \|/-\|/-\|/-\|/-\|/-\|/-\ [ 0.518488] mmcblk0: p1 p2 < p5 > [ 0.519323] |/- [ 0.521018] mmc1: new loftier speed SDIO carte at address 0001 [ 0.521584] \|/-\ [ 0.524589] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43455-sdio for scrap BCM4345/6 [ 0.524686] brcmfmac mmc1:0001:1: Straight firmware load for brcm/brcmfmac43455-sdio.bin failed with error -two [ 0.524691] brcmfmac mmc1:0001:1: Falling back to sysfs fallback for: brcm/brcmfmac43455-sdio.bin [ 0.524782] |/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\ [ 0.558447] |/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\ [ 0.592384] |/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/done. [ 0.683690] VFS: Mounted root (squashfs filesystem) readonly on device 1:0. [ 0.683878] devtmpfs: mounted [ 0.684921] Freeing unused kernel retention: 2048K [ 0.717257] Run /init every bit init process [ 0.757124] usb 1-1: new loftier-speed USB device number two using xhci_hcd [ 0.781657] uart-pl011 fe201000.series: no DMA platform data [ 0.921620] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43455-sdio for chip BCM4345/six [ 0.930993] brcmfmac: brcmf_c_preinit_dcmds: Firmware: BCM4345/half dozen wl0: Mar 23 2022 02:19:54 version vii.45.206 (r725000 CY) FWID 01-88ee44ea [ 0.939741] usb 1-1: New USB device plant, idVendor=2109, idProduct=3431, bcdDevice= 4.21 [ 0.939746] usb 1-i: New USB device strings: Mfr=0, Product=i, SerialNumber=0 [ 0.939750] usb one-i: Product: USB2.0 Hub [ 0.941297] hub i-1:i.0: USB hub found [ 0.941616] hub ane-one:ane.0: 4 ports detected [ 1.267101] usb i-1.2: new total-speed USB device number 3 using xhci_hcd [ 1.406951] usb one-1.two: New USB device found, idVendor=24ae, idProduct=1001, bcdDevice= 1.07 [ one.406956] usb 1-one.2: New USB device strings: Mfr=1, Product=two, SerialNumber=0 [ 1.406960] usb ane-one.2: Product: Rapoo ii.4G Wireless Bear upon Desktop [ 1.406964] usb one-1.2: Manufacturer: MOSART Semi. [ 1.413583] input: MOSART Semi. Rapoo 2.4G Wireless Touch Desktop as /devices/platform/scb/fd500000.pcie/pci0000:00/0000:00:00.0/0000:01:00.0/usb1/1-1/i-1.two/ane-1.2:1.0/0003:24AE:1001.0001/input/input0 [ 1.477292] hid-generic 0003:24AE:1001.0001: input,hidraw0: USB HID v1.10 Keyboard [MOSART Semi. Rapoo 2.4G Wireless Touch Desktop ] on usb-0000:01:00.0-1.2/input0 [ one.484977] input: MOSART Semi. Rapoo 2.4G Wireless Affect Desktop Mouse equally /devices/platform/scb/fd500000.pcie/pci0000:00/0000:00:00.0/0000:01:00.0/usb1/i-1/1-1.2/1-1.two:1.1/0003:24AE:1001.0002/input/input1 [ 1.485142] input: MOSART Semi. Rapoo ii.4G Wireless Bear on Desktop Consumer Command as /devices/platform/scb/fd500000.pcie/pci0000:00/0000:00:00.0/0000:01:00.0/usb1/1-1/one-one.two/one-ane.ii:ane.one/0003:24AE:1001.0002/input/input2 [ 1.547188] input: MOSART Semi. Rapoo ii.4G Wireless Bear upon Desktop System Command as /devices/platform/scb/fd500000.pcie/pci0000:00/0000:00:00.0/0000:01:00.0/usb1/one-1/1-1.2/ane-one.ii:1.one/0003:24AE:1001.0002/input/input3 [ 1.547272] input: MOSART Semi. Rapoo 2.4G Wireless Touch Desktop as /devices/platform/scb/fd500000.pcie/pci0000:00/0000:00:00.0/0000:01:00.0/usb1/1-1/1-1.2/1-one.ii:1.1/0003:24AE:1001.0002/input/input4 [ 1.547357] hid-generic 0003:24AE:1001.0002: input,hidraw1: USB HID v1.ten Mouse [MOSART Semi. Rapoo 2.4G Wireless Touch Desktop ] on usb-0000:01:00.0-1.ii/input1 [ 1.831017] EXT4-fs (mmcblk0p5): INFO: recovery required on readonly filesystem [ 1.831021] EXT4-fs (mmcblk0p5): write admission will exist enabled during recovery [ 1.854428] EXT4-fs (mmcblk0p5): recovery complete [ 1.857186] EXT4-fs (mmcblk0p5): mounted filesystem with ordered information mode. Opts: (nix) [ ane.908622] EXT4-fs (mmcblk0p5): mounted filesystem with ordered data mode. Opts: (null) [ 1.927590] random: dbus-uuidgen: uninitialized urandom read (12 bytes read) [ i.927611] random: dbus-uuidgen: uninitialized urandom read (eight bytes read) [ 1.936925] random: dbus-daemon: uninitialized urandom read (12 bytes read) [ ii.108245] brcmfmac: brcmf_cfg80211_set_power_mgmt: power save enabled [ 2.177473] bcmgenet: Skipping UMAC reset [ two.178594] bcmgenet fd580000.ethernet: configuring instance for external RGMII [ 2.178754] bcmgenet fd580000.ethernet eth0: Link is Downwardly [ 7.560506] urandom_read: iii callbacks suppressed [ 7.560509] random: wpa_supplicant: uninitialized urandom read (32 bytes read) [ 7.586052] random: dhcpcd: uninitialized urandom read (120 bytes read) [ eight.267127] random: dhcpcd: uninitialized urandom read (120 bytes read) [ 61.655669] random: crng init done [ 61.655674] random: i urandom warning(s) missed due to ratelimiting [ 386.287102] usb ane-1.iii: new high-speed USB device number four using xhci_hcd [ 386.419588] usb one-ane.iii: New USB device found, idVendor=04e8, idProduct=1d23, bcdDevice= 1.10 [ 386.419593] usb one-ane.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 386.419597] usb 1-ane.3: Product: Mighty Drive [ 386.419601] usb 1-one.iii: Manufacturer: Samsung [ 386.419605] usb one-1.3: SerialNumber: 07731091A1A9 [ 386.420947] usb-storage 1-1.iii:1.0: USB Mass Storage device detected [ 386.421061] scsi host0: usb-storage ane-1.3:1.0 [ 387.447782] scsi 0:0:0:0: Straight-Access Samsung Mighty Bulldoze PMAP PQ: 0 ANSI: 0 CCS [ 388.500670] sd 0:0:0:0: [sda] 4029440 512-byte logical blocks: (2.06 GB/1.92 GiB) [ 388.500797] sd 0:0:0:0: [sda] Write Protect is off [ 388.500802] sd 0:0:0:0: [sda] Mode Sense: 23 00 00 00 [ 388.500925] sd 0:0:0:0: [sda] No Caching way page institute [ 388.506967] sd 0:0:0:0: [sda] Bold drive cache: write through [ 388.558397] sda: sda1 [ 388.559092] sd 0:0:0:0: [sda] Attached SCSI removable disk [ 443.102100] FAT-fs (sda1): Volume was non properly unmounted. Some data may be decadent. Please run fsck.Alles anzeigen
-
- #7
Nein.
Poste mal nach einem:
echo 1 > /sys/bus/pci/devices/0000\:01\:00.0/remove(... damit werden die USB-Anschlüsse deaktiviert), die Ausgabe von:
ganz überlesen, sorry...
der Teil von dmesg nach deinem Befehl und lsusb
root@raspberrypi:/habitation/pi# sudo echo ane > /sys/bus/pci/devices/0000\:01\:00.0/remove root@raspberrypi:/home/pi# dmesg ....... ....... [ 43.008036] xhci_hcd 0000:01:00.0: remove, state 4 [ 43.008071] usb usb2: USB disconnect, device number 1 [ 43.009646] xhci_hcd 0000:01:00.0: USB bus ii deregistered [ 43.009752] xhci_hcd 0000:01:00.0: remove, state 1 [ 43.009780] usb usb1: USB disconnect, device number 1 [ 43.137609] xhci_hcd 0000:01:00.0: USB omnibus 1 deregistered root@raspberrypi:/dwelling house/pi# lsusb root@raspberrypi:/domicile/pi#Alles anzeigen
-
- #8
der Teil von dmesg nach deinem Befehl und lsusb
[ 43.008036] xhci_hcd 0000:01:00.0: remove, state four [ 43.008071] usb usb2: USB disconnect, device number 1 [ 43.009646] xhci_hcd 0000:01:00.0: USB bus ii deregistered [ 43.009752] xhci_hcd 0000:01:00.0: remove, state 1 [ 43.009780] usb usb1: USB disconnect, device number 1 [ 43.137609] xhci_hcd 0000:01:00.0: USB bus 1 deregisteredHmm, bei mir sind ii Zeilen mehr:
[607142.546765] xhci_hcd 0000:01:00.0: remove, land 4 [607142.546804] usb usb2: USB disconnect, device number 1 [607142.548306] xhci_hcd 0000:01:00.0: USB motorcoach ii deregistered [607142.548431] xhci_hcd 0000:01:00.0: remove, country 4 [607142.548465] usb usb1: USB disconnect, device number 1 [607142.548487] usb 1-1: USB disconnect, device number 2 [607142.553352] xhci_hcd 0000:01:00.0: USB passenger vehicle ane deregisteredxhci_hcd 0000:01:00.0: remove, state fourund
usb one-1: USB disconnect, device number 2
Source: https://forum-raspberrypi.de/forum/thread/50016-rb-pi-4-4gb-bootet-usb-nicht-funtkional/
Post a Comment for "Usb 1-1.2.1: Device Descriptor Read/64, Error -71"